API STD 677-2021
通用、擠出機及行星齒輪裝置規范
Specification for general purpose, extruder and planetary gear units
- 標準號
- API STD 677-2021
- 發布
- 2021年
- 總頁數
- 188頁
- 發布單位
- 美國石油學會
- 當前最新
- API STD 677-2021
- 引用標準
- AGMA 925-A03 ANSI/AGMA 2001-D04 ANSI/AGMA 2101-D04 ANSI/ASME B1.20.1 ANSI/ASME B16.1 ANSI/ASME B16.11 ANSI/ASME B16.42 ANSI/ASME B16.5 ANSI/ASME B31.3 ASME B1.13M ASME B16.47 ASME B17.1 ASME PTC 36 ASTM A1 ASTM A106/A106M ASTM A181/A181M ASTM A192/A192M ASTM A193/A193M ASTM A194/A194M ASTM A247 ASTM A269/A269M ASTM A275/A275M ASTM A307 ASTM A312/A312M ASTM A32 ASTM A388/A388M ASTM A524 ASTM A609/A609M ASTM E1 ASTM E165/E165M ASTM E709 ASTM E94/E94M ASTM F104 EN 10084 EN 10085 EN 1092-2 EN 1561 EN 1563 IEC 60529 ISO 1328-1 ISO 14635-1 ISO 14732 ISO 15 ISO 21940-11 ISO 21940-12 ISO 261 ISO 262 ISO 281 ISO 3290 ISO 3448 ISO 355 ISO 3744 ISO 3746 ISO 4386-1 ISO 4386-3 ISO 492 ISO 5753-1 ISO 582 ISO 6336-5 ISO 6708 ISO 7005-1 ISO 7005-2 ISO 724 ISO 76 ISO 8501 ISO 9606-1 ISO/R 286 ISO/R 775 ISO/TS 6336-21 MSS SP-55 NEMA 250
- 適用范圍
- This standard covers the minimum requirements for general-purpose, enclosed single and multistage gear units incorporating parallel shaft spur, and helical gears for use in the petroleum, chemical, and gas industry services. General-purpose and extruder gears manufactured according to this standard are limited to pitch line velocities that do not exceed 60 m/s (12,000 ft/min). The requirements for parallel shaft helical gears applied to extruder services are included in Section 9 of this standard. The requirements for epicyclic gears driving equipment, such as electrical generators, centrifugal compressors, and pumps, are included in Section 10 of this standard. This standard does not apply to gears in special-purpose service, which are covered in API 613, to gears integral with other equipment, or gears with noninvolute tooth forms. NOTE General-purpose gears are applied in equipment trains that are usually spared, or are in noncritical service. Typical applications for which this standard is intended are cooling tower water pump systems, forced and induced draft fan systems, and other general-purpose equipment trains.
| 術語 | 描述 |
|---|---|
| 頂點 apex | 雙斜齒輪左右傾斜（螺旋）相遇的點所定義的平面。 |
| 頂點跳動 apex runout | 制造過程中產生的頂點平面的輕微偏差。 |
| 軸向浮動 axial float | 軸沿其旋轉軸線的自由運動，通常由推力軸承間隙或齒輪嚙合間隙或兩者的組合限制。 |
| 軸向分裂接頭 axially split joint | 主面與軸中心線平行的分裂接頭。 |
| 背隙 backlash | 在操作節徑上，齒槽寬度超過嚙合齒厚的量。 |
| 彎曲應力數 bending stress number | 對應于齒根疲勞裂紋的可能性，如果過大，可能導致齒輪齒的失效。 |
| 布氏硬度 Brinell hardness | 材料抵抗壓痕的特性，不是基本的物理性質。 |